Assessment of the performance of a symbiotic microalgal-bacterial granular sludge reactor for the removal of nitrogen and organic carbon from dairy wastewater.

Cheese whey (CW) is a nutrient deficient dairy effluent, which requires external nutrient supplementation for aerobic treatment. CW, supplemented with ammonia, can be treated using aerobic granular sludge (AGS) in a sequencing batch reactor (SBR). AGS are aggregates of microbial origin that do not coagulate under reduced hydrodynamic shear and settle significantly faster than activated sludge flocs. However, granular instability, slow granulation start-up, high energy consumption and CO2 emission have been reported as the main limitations in bacterial AGS-SBR. Algal-bacterial granular systems have shown be an innovative alternative to improve these limitations. Unfortunately, algal-bacterial granular systems for the treatment of wastewaters with higher organic loads such as CW have been poorly studied. In this study, an algal-bacterial granular system implemented in a SBR (SBRAB) for the aerobic treatment of ammonia-supplemented CW wastewaters was investigated and compared with a bacterial granular reactor (SBRB). Mass balances were used to estimate carbon and nitrogen (N) assimilation, nitrification and denitrification in both set-ups. SBRB exhibited COD and ammonia removal of 100% and 94% respectively, high nitrification (89%) and simultaneous nitrification-denitrification (SND) of 23% leading to an inorganic N removal of 30%. The efficient algal-bacterial symbiosis in granular systems completely removed COD and ammonia (100%) present in the dairy wastewater. SBRAB microalgae growth could reduce about 20% of the CO2 emissions produced by bacterial oxidation of organic compounds according to estimates based on synthesis reactions of bacterial and algal biomass, in which the amount of assimilated N determined by mass balance was taken into account. A lower nitrification (75%) and minor loss of N by denitrifying activity (<5% Ng, SND 2%) was also encountered in SBRAB as a result of its higher biomass production, which could be used for the generation of value-added products such as biofertilizers and biostimulants.

Performance of oxalic acid-chitosan/alumina ceramic biocomposite for the adsorption of a reactive anionic azo dye.

A biocomposite system was developed and tested for the removal of the azo dye Reactive Red (RR195) from wastewater. The biocomposite was synthesized using ceramic particles containing 75% alumina which were coated using chitosan cross-linked with oxalic acid. The biocomposite showed high performance at low pH (maximum adsorption capacity = 345.3mg.g-1 at pH=2.0). The physicochemical and structure characteristics of the matrix were evaluated by Z-potential, FTIR-ATR, SEM-EDS, XRD, and porosity. Langmuir sorption isotherm and pseudosecond-order model gave the best fit. The electrostatic interaction between RR195 (due to the sulfonate groups) and the free amino groups of chitosan, enabled successive desorption/regeneration cycles. The maximum removal percentage (>80%) occurred at pH=2.0 due to the cross-linking effect. Experiments at different temperatures allowed the calculation of thermodynamic parameters (ΔG, ΔS, ΔH); adsorption was spontaneous, exothermic, and enthalpy controlled. The presence of inorganic ions ([Formula: see text] ) was analyzed during the adsorption process. This novel biocomposite can be applied as a cost-effective and environmentally friendly adsorbent for anionic azo dye removal from wastewater. The application of chitosan cross-linked with oxalic acid as a coating of the ceramic support enhanced the adsorption capacity and enabled its use under acidic conditions without solubilization.

New insights into halophilic prokaryotes isolated from salting-ripening anchovies (Engraulis anchoita) process focused on histamine-degrading strains.

Salted and ripened fish foods are susceptible to cause histamine poisoning. The present study focuses on microbial histamine degradation from high salted fermented fishery products to deepen our understanding about this new and growing field of research. As a result of this first study related to salted-ripened anchovies (Engraulis anchoita), fifty seven moderate and extreme halophilic microbial isolates from salt and salted-ripened anchovy processes were characterized in terms of their phenotype and histamine-degrading capacity. Only 7%-4 isolates-were able to degrade histamine. None of the histamine-degrading isolates presented proteolytic and/or lipolytic activity. One of them designated A18 was chemotactic toward histamine, an interesting property not previously reported for that chemoattractant. However, the S18 and A18 isolates, genotypically identified as Halobacterium sp. and Halomonas sp. respectively, produced indole and/or H2S, both undesirable characteristics associated to off-flavors occurrence. On the other hand, A28 and S20, identified as Halovibrio sp. and Halobacterium sp. respectively, presented desirable properties, such as cytochrome oxidase and catalase activity, and non-production of H2S and indole. These strains also showed characteristics previously reported as dominant in the ripened stage. The results are promising, and A28 and S20 may have the desirable features to improve the anchovy salting-ripening process.

Functional iron chitosan microspheres synthesized by ionotropic gelation for the removal of arsenic (V) from water.

Arsenic (As) is considered one of the most serious inorganic contaminants in groundwater. The maximum limit of As in drinking water is 0.010mgAs L-1 according to the World Health Organization. Functional Iron Chitosan Microspheres (F-ICM) were synthesized by ionotropic gelation of chitosan and ferric nitrate for removal of As (V) from water. The effects of iron concentration (0.7, 5.5 and 11.2gFe+3/100g chitosan), pH range (4-9), sorbent dosage, possibility of reuse and presence of interfering anions were analyzed. F-ICM were effective for As (V) adsorption in a wide range of pH with removals higher than 88.9%, reaching concentrations < 0.010mgAs L-1. A higher proportion of iron in the matrix favored the removal of As(V) in a pH range 6 to 9. Kinetic data of As(V) adsorption onto 0.7 F-ICM under all tested initial concentrations fitted well with the pseudo second-order kinetic model. Sorption isotherm experimental data were satisfactorily fitted with the Langmuir equation; the maximum sorption capacity for As(V) was 120.77mgAs(V) (gF-ICM1) and the Langmuir constant was 0.331 L mg1. A good performance of the adsorption capacity was obtained in four successive adsorption cycles of reuse and in the presence of interfering anions, indicating the high adsorption capacity of the synthesized microspheres.

Nanoferulic: From a by-product of the beer industry toward the regeneration of the skin.

BACKGROUND: Brewers' spent grain (BSG) is one of the most abundant by-products of the beer industry and causes serious environmental problems. Ferulic acid (FA) is an antioxidant with potential cosmeceutical applications. FA was extracted from BSG, developing a method of high extraction performance in order to be encapsulated in ultradeformable liposomes (Nanoferulic, NF). AIMS: To obtain a product with high added value such as FA, from a residue currently underused, using simple and economical chemical methods. To load FA into a nanosystem designed for the topical route, its encapsulation has the purpose to take profit from its photoprotective, anti-inflammatory, and antioxidant properties in the deep layers of the skin. METHODS: Ferulic acid was obtained from dried BSG using acid and basic treatments in series. NF was prepared by lipid film resuspension of a solution containing FA obtained from BSG. Size and Z-potential were determined. Cytotoxicity was assessed in vitro. Skin penetration was assessed by NF determination at different skin depths and by confocal microscopy. RESULTS: The yield of the extraction process was 0.43% on a dry basis. Encapsulation rendered liposomes of around 140 nm with 92% of encapsulation efficiency. No toxicity was observed in all the tested concentrations. Successful results were obtained from the regeneration studies. CONCLUSIONS: It was possible to develop a nanosystem containing FA, generating a high-value commercial input for the pharmaceutical and cosmeceutical industry. The use of BSG generated in industrial scale would help to reduce the volume of highly polluting waste.

Effect of the desiccation tolerance and cryopreservation methods on the viability of Citrus limon L. Burm cv. Eureka seeds.

Cryopreservation of the germplasm for long-term periods is of great importance to maintain the genetic resource. Argentina is one of the world's highest lemon producing country. The performance of different cooling/warming rates in the cryopreservation method of Citrus limon L. Burm cv. Eureka seeds and their influence on the interval of optimal moisture content in the desiccation stage were analyzed. Water sorption isotherm was determined and modeled using D'Arcy & Watt equation; it provided important information concerning the amounts of water associated to strong, weak and multimolecular binding sites along the sorption isotherm. Seeds tolerated a wide range of desiccation conditions (0.180%), however desiccation to 0.0526 g H2O g-1 d.b. (aw = 0.0901) produced a significant loss of viability. Differential Scanning Calorimetry was used to identify the thermal transitions of lipids and water in the seed; enthalpies were used to calculate the unfrozen water fraction (0.19 g H2O g-1 d.b. corresponding to aw = 0.64). Two cooling/warming rates were tested on desiccated seeds (0.110.64 corresponding to the unfrozen water fraction. The use of higher cooling/warming rates enables a wider range of desiccation conditions (0.33

Monitoring the characteristics of cultivable halophilic microbial community during salted-ripened anchovy (Engraulis anchoita) production.

The halophilic microbial community of the salted-ripened anchovy process was studied. Samples from raw materials (salt and fresh anchovies) and from the stages of brining and ripening were collected and analyzed for their bacterial counts at 15 and 20% NaCl. No halophilic colonies were found in fresh anchovy and counts of about 103 CFU/g were determined in salt samples. A fluctuation of bacterial counts during the process was found. At the end of brining, ~104 CFU/g were determined in anchovy samples and this value was reduced to not detectable counts at the beginning of the ripening stage. After one month, counts increased to ~104 CFU/g and remained stable until the end of the process. From each sample, colonies having different morphotypes were isolated and submitted to a macro and microscopic characterization, a study of salt requirement for growth, and biochemical and phenotypic tests. The results were submitted to Univariate, Bivariate and Multiple Correspondence Factorial Analysis (MCFA). A total of 79 colonies were isolated during the salting-ripening anchovy process. Among the isolates, about 40-50% was positive for indole production and lipolytic activity and a 25% showed ability to produce H2S and proteolytic capacity. Proteolytic and lipolytic activities were well balanced along the process and resulted independent from the isolation stage, which is a desirable condition due to the contribution of microbial proteolysis and lipolysis to the development of texture and final aroma, respectively. H2S and indole producers practically were not detected during ripening. This fact is important because indole and H2S are associated with the development of off-flavors and spoilage in salted fish products. MFCA and Cluster Analyses complemented the Bivariate Analyses. The factor map showed proximity between the isolates from salt samples and from ripening. Isolates were statistically clustered in two groups. Cluster 1 grouped non-desirable activities (H2S and indole production) with cultures proceeding from brining whereas Cluster 2 related isolates mainly from salt samples and during ripening with some desirable microbial capacities (Cytochrome oxidase activity and non-H2S and non-indole production). These results would indicate that during the ripening process of salted anchovies, a natural selection of beneficial microorganisms for the development of the typical product sensory attributes occurred.

Microstructural Behaviors of Matrices Based on Polylactic Acid and Polyhydroxyalkanoates.

Individual films of polyhydroxyalkanoates (PHA) and polylactic acid (PLA) and their blends were developed by solvent casting. PHA was obtained from activated sludges from a wastewater-treatment system at a laboratory scale. This work focused on analyzing the microstructural properties and thermal behaviors of individual films of PHA and PLA as well as those of their blends. The behaviors of the biodegradation processes of the individual films and blends were examined from a microstructural point of view. ATR-FTIR spectra indicated the existence of weak molecular interactions between the polymers. The formulation of blend films improved the crystallinity of PLA; additionally, it induced the polymer-recrystallization phenomenon, because crystallized PHA acted as a PLA-nucleating agent. This phenomenon explains the improvements in the films' water-vapor-barrier properties. The blends exposed to a biodegradation process showed an intermediate behavior between PLA and PHA, leading to a consistent basis for designing systems tailored to a particular purpose.

In-vitro development of vitrified-warmed bovine oocytes after activation may be predicted based on mathematical modelling of cooling and warming rates during vitrification, storage and sample removal.

Heat transfer during cooling and warming is difficult to measure in cryo-devices; mathematical modelling is an alternative method that can describe these processes. In this study, we tested the validity of one such model by assessing in-vitro development of vitrified and warmed bovine oocytes after parthenogenetic activation and culture. The viability of oocytes vitrified in four different cryo-devices was assessed. Consistent with modelling predictions, oocytes vitrified using cryo-devices with the highest modelled cooling rates had significantly (P < 0.05) better cleavage and blastocyst formation rates. We then evaluated a two-step sample removal process, in which oocytes were held in nitrogen vapour for 15 s to simulate sample identification during clinical application, before being removed completely and warmed. Oocytes exposed to this procedure showed reduced developmental potential, according to the model, owing to thermodynamic instability and devitrification at relatively low temperatures. These findings suggest that cryo-device selection and handling, including method of removal from nitrogen storage, are critical to survival of vitrified oocytes. Limitations of the study include use of parthenogenetically activated rather than fertilized ova and lack of physical measurement of recrystallization. We suggest mathematical modelling could be used to predict the effect of critical steps in cryopreservation.

Monitoring and modeling 4-chlorophenol biodegradation kinetics by phenol-acclimated activated sludge by using open respirometry.

The aim of this study was to analyze the mechanisms, stoichiometry, and stability of 4-chlorophenol (4CP) biodegradation kinetics by phenol-acclimated activated sludge using open respirometry. While the removal of 4CP was higher than 98%, the removal of chemical oxygen demand (COD) ranged between 69 and 79% due to the accumulation of an intermediate metabolite. The value obtained from respirometric profiles for the stoichiometric ratio of O2 to 4CP (YO2/4CP) was 1.95 ± 0.04 mol of oxygen consumed per mol of 4CP removed. This YO2/4CP value reflected the action of the oxygenases responsible for the first steps of the aerobic oxidation of 4CP. The 4CP degradation activity decreased noticeably when successive pulses of 4CP were added to the respirometer. A mathematical model was developed to represent the aerobic biodegradation of 4CP. The fitted model adequately predicted the oxygen consumption rate, total phenols, and soluble COD concentrations as a function of time. The results presented could help to predict the dynamic of biodegradation of chlorophenols in a biological wastewater treatment system.

Kinetic Parameters for the Thermal Inactivation of Peroxidase and Lipoxygenase in Precooked Frozen Brassica Species.

Thermal inactivation of peroxidase (POD) and lipoxygenase (LOX), both enzymes present in broccoli and Brussels sprouts, is required before freezing, to obtain high-quality precooked frozen vegetables. Rate constants of a 1st-order biphasic model for the heat-labile and heat-resistant POD and LOX isoenzymes were determined at different temperatures (75, 80, and 90 °C) and the corresponding activation energies were estimated using nonlinear regressions. In the case of Brussels sprouts, the activation energies for the resistant and labile fractions were 56.3 and 62.5 kJ/mol for POD and 63.7 and 65.8 kJ/mol for LOX, respectively. For Brussels sprouts, different precooking times were tested to analyze the effect of residual enzyme activity on quality parameters and sensory attributes, after a frozen storage of 4 mo at -20 °C. A significant reactivation of enzyme activity after frozen storage was observed (especially in the case of POD) for short precooking times (<6 min) leading to low-quality parameters at the interior zone of the vegetable. A precooking time of 6 min at 90 °C allowed an adequate inactivation of LOX and POD obtaining a high-quality final frozen vegetable. A sensory analysis confirmed the global acceptability of the product. The obtained results are relevant to define the precooking stage conditions in the production of frozen cruciferous vegetables.

Effect of sweetener combination and storage temperature on physicochemical properties of sucrose free white chocolate.

The influence of a combination of sweeteners (Stevia (St) and sucralose (Su)) and storage temperature on thermal properties, microstructure, water content, texture and Bloom of sucrose free white chocolate was investigated. A strong relationship between the microstructure and the highest percentage of Bloom was observed. The samples with 100%Su and 50%S+50%Su presented microstructures with channels through which solids and fat could more easily spread to the surface, increasing the fat and sugar Bloom formation. However, 50%St+50%Su and 75%St+25%Su samples showed a minimum Bloom formation, probably due to its dense microstructure with no void spaces. The differential scanning calorimetry studies demonstrated that the samples containing 100%St and 75%St+25%Su showed the smallest decrease of melting enthalpy with increasing temperature. Besides, non-isothermal crystallization kinetics was studied by applying Avrami model. The sample 75%St+25%Su presented the highest values of activation energy showing the greatest stability in the temperature range studied (7°C-30°C).

Influence of hydrogenated oil as cocoa butter replacers in the development of sugar-free compound chocolates: Use of inulin as stabilizing agent.

The effect of the addition of inulin as a surfactant or stability agent on white compound chocolate sweetened with sucralose and Stevia was studied. Samples were stored at 7, 15 and 30°C during 100days and the influence of inulin on rheological properties, sensorial attributes, shelf-life, physical properties such as melting, crystallization and blooming were analyzed. The shelf-life of the compound chocolate with the incorporation of inulin was higher than the control sample without replacement. Compound chocolate with inulin at 10%w/w showed a dense matrix structure, reducing the size and number of fat crystals formed during storage; furthermore they presented higher values of brightness and WI. This chocolate also showed less fracturability and improved thermal properties. DSC studies revealed increased values of onset and peak temperatures and enthalpy of melting of the polymorphic form V, at higher storage temperatures, achieving greater stability against degradation processes.

Nitrification and aerobic denitrification in anoxic-aerobic sequencing batch reactor.

The aim of this study was to evaluate the feasibility of achieving nitrogen (N) removal using a lab-scale sequencing batch reactor (SBR) exposed to anoxic/aerobic (AN/OX) phases, focusing to achieve aerobic denitrification. This process will minimize emissions of N2O greenhouse gas. The effects of different operating parameters on the reactor performance were studied: cycle duration, AN/OX ratio, pH, dissolved oxygen concentration (DOC), and organic load. The highest inorganic N removal (NiR), close to 70%, was obtained at pH=7.5, low organic load (440mgCOD/(Lday)) and high aeration given by 12h cycle, AN/OX ratio=0.5:1.0 and DOC higher than 4.0mgO2/L. Nitrification followed by high-rate aerobic denitrification took place during the aerobic phase. Aerobic denitrification could be attributed to Tetrad-forming organisms (TFOs) with phenotype of glycogen accumulating organisms using polyhydroxyalkanoate and/or glycogen storage. The proposed AN/OX system constitutes an eco-friendly N removal process providing N2 as the end product.

Hexavalent chromium removal in contaminated water using reticulated chitosan micro/nanoparticles from seafood processing wastes.

Chitosan particles (CH) were obtained from seafood processing wastes (shrimp shells) and physicochemically characterized; deacetylation degree of CH was measured by Infrared Spectroscopy (FTIR) and potentiometric titration; polymer molecular weight was determined by intrinsic viscosity measurements. Reticulated micro/nanoparticles of chitosan (MCH) with an average diameter close to 100nm were synthesized by ionic gelation of chitosan using tripolyphosphate (TPP), and characterized by SEM, size distribution and Zeta-potential. Detoxification capacities of CH and MCH were tested analyzing the removal of hexavalent chromium Cr(VI) from contaminated water, at different initial chromium concentrations. The effect of pH on adsorption capacity of CH and MCH was experimentally determined and analyzed considering the Cr(VI) stable complexes (anions) formed, the presence of protonated groups in chitosan particles and the addition of the reticulating agent (TPP). Chitosan crosslinking was necessary to adsorb Cr(VI) at pH<2 due to the instability of CH particles in acid media. Langmuir isotherm described better than Freundlich and Temkin equations the equilibrium adsorption data. Pseudo-second order rate provided the best fitting to the kinetic data in comparison to pseudo-first order and Elovich equations. Chemical analysis to determine the oxidation state of the adsorbed Cr, showed that Cr(VI) was adsorbed on CH particles without further reduction; in contrast Cr(VI) removed from the solution was reduced and bound to the MCH as Cr(III). The reduction of toxic Cr(VI) to the less or nontoxic Cr(III) by the reticulated chitosan micro/nanoparticles can be considered a very efficient detoxification technique for the treatment of Cr(VI) contaminated water.

Mechanical and optical characterization of gelled matrices during storage.

The effect of composition and storage time on the rheological and optical attributes of multi-component gels containing locust bean gum (LBG), low acyl (LAG) and high acyl (HAG) gellan gums, was determined using three-component mixture design. The generalized Maxwell model was used to fit experimental rheological data. Mechanical and relaxation spectra of gelled systems were determined by the type of gellan gum used, except LBG alone which behaved as a diluted gum dispersion. Storage time dependence of the gels was analyzed using the rubber elasticity theory and to determine changes in network mesh size the equivalent network approach was applied. Destabilization kinetic was obtained from light scattering results; increasing LAG content improved the long-term stability of the matrices. Almost every formulation exhibited an increment in both moduli during the first 10 days remaining practically constant thereafter or until they broke (binary mixtures with LBG); gels with HAG/LBG mixtures were the least stable.

Physicochemical characteristics and quality parameters of a beef product subjected to chemical preservatives and high hydrostatic pressure.

The use of high hydrostatic pressure (HHP) on fresh beef causes a deleterious effect on red colour. A beef product subjected to HHP exhibiting acceptable colour and microbiological stability was developed; the process requires as a first step the immersion in a preservative solution containing ascorbic acid, sodium nitrite, and sodium chloride. Desirability functions were used to optimise the composition of this solution in order to maintain the colour attributes minimising the concentration of sodium nitrite. The product was packed in low gas permeability film before HHP treatment. The effect of the applied pressure (300, 600 MPa) on quality parameters (colour,texture) was analysed. The stability of the product during storage at 4 °C was determined by microbial counts, colour, texture, and exudate. The combination of treatments provided acceptable colour and microbiological stability during four and six weeks of refrigerated storage after the product has been subjected to 300 and 600 MPa, respectively.

Potassium sorbate controlled release from corn starch films.

Active starch films with glycerol and potassium sorbate were obtained by casting. Native and acetylated corn starches, as well as the mixture of them in equal proportions were used and filmogenic suspensions with pH 4.5 were also prepared. Sorbate concentration decreased during film storage due to its oxidative degradation. Active films resulted more yellow and less transparent than films without sorbate. The minimum inhibitory concentration of sorbate resulted 0.3%, regardless of the starch type and the formulation pH. The use of antimicrobial package was more effective to prevent microbial growth on food surfaces than the use of conventional methods. Additive kinetic release was neither affected by the starch type nor by the formulation pH. Sorbate diffusion process was mathematically modeled satisfactorily. Active films were able to inhibit Candida spp., Penicillium spp., S. aureus and Salmonella spp. growth. Active films extended 21% the shelf life of refrigerated cheese, regardless of the formulation pH.

Thermoplastic starch films reinforced with talc nanoparticles.

Nanocomposite films of thermoplastic corn starch (TPS) with talc particles were obtained by thermo-compression in order to study the effect of filler on structure, optical, and thermal properties. Talc increased the films rigid phase, thus their cross-sections resulted more irregular. Talc preferential orientation within matrix and good compatibility between particles and TPS was observed by SEM. Slight crystalline structure changes in TPS matrix were measured by XRD and DSC, due to talc nucleating effect. Randomly dispersed talc nanoagglomerates and individual platelets were assessed by TEM. Laminar morphology and nano-sized particles allowed that nanocomposite films were optically transparent. TPS-talc films resulted heterogeneous materials, presenting domains rich in glycerol and others rich in starch. Talc incorporation higher than 3%, w/w increased softening resistance of the nanocomposites as stated by DMA. Relaxation temperatures of glycerol-rich phase shifted to higher values since talc reduces the mobility of starch chains.

Stabilizing effect of saccharides on bovine plasma protein: a calorimetric study.

Bovine plasma proteins provide the needed amino acids for the growth and development of an organism. With the purpose of preserving the native structure, related with the protein functional properties, the oligosaccharide inulin was used as protective agent and was compared with glucose and sucrose, during freeze-drying. In the present study, the thermal stability of protein was investigated as a function of type of saccharide in a concentration range of 5-15% (w/v), and at different pHs. The effect of these variables on phase transition, thermal stability and miscibility was assessed by differential scanning calorimetry (DSC) and scanning electron microscopy (SEM). The results of thermal protein properties (denaturation temperature and enthalpy), demonstrated that endothermic transition shifted to higher temperatures, being the stabilizing effect: inulin>glucose>sucrose. The thermal behavior suggests compatibility or interactions between the components of blends. In this way, the micrographs showed a homogeneous distribution of the different phases, corroborating the miscibility in the matrix. The unfolding process was irreversible and could be adequately described by a two-state model.